Restoration Hardware

screws2

Yes, I am a vintage hardware nerd.

Every time I extract a screw from an old piece of furniture I have to pause and marvel at the beauty and craftsmanship that went into these quality controlled fastening devices. Just look at those cleanly cut threads and the polished heads. You won’t find anything close to this quality at Home Depot or the like. Anybody who’s ever searched through the bins looking for a screw that doesn’t have threads that look like they’ve been chewed on by an angry giraffe knows what I’m talking about.

They don’t make them like this anymore. Why not?  Can I get an Amen!!

Advertisements

Removing Black Stains

Today’s project brings us more embarrassing black stains to be removed. This is an American of Martinsville end table that needs some attention.

-The first photo shows the top of the table with a multitude of black stains and scratches.

aom2

-Here I’m applying oxalic acid to the black stains to bleach them out. At this point I’ve already stripped off whatever was left of the original finish.

aom4

-This photo shows the top with fresh stain and little to no black stains left. The oxalic acid did a great job on this one.

aom3

-And here’s the finished product. Nice!

aom5

-Beforeaom8

-Afteraom6

Lane Perception Restoration

rest7

Here’s the story of an old Lane Perception nightstand that’s seen better days. It’s got flaking finish, black rings, loose trim, chipped veneer and a broken drawer pull. Can this poor table be brought back to life? Follow along and find out!

Stripping the Existing Finish

rest2

This is the least enjoyable step and is best left to your minions. I don’t like to get my hands dirty so I’m usually out on the links while the stripping is underway but my minions tell me that their preferred method of stripping the finish on this piece was to scrape it off. This can be done with a card scraper or even a utility knife blade. Scraping works particularly well when the original finish has already begun flaking off as it had on this table. Scraping is also a lot less messy than using a chemical stripper and is cheaper since you don’t have to buy stripper and the scraper can be used over and over and over again. This isn’t always the best method and often a chemical stripper is necessary.

Black Ring Removal

rest4.2

I first tried sanding this ring out but it was in there too deep so instead I used oxalic acid. Oxalic acid is usually sold in stores as wood bleach. I just dabbed a bit on the black areas with a small paintbrush, let it sit for 5-10 minutes and then washed it off. It worked well as you can see in the pictures. There’s still a hint of the black lines left but they are running in the same direction as the grain so it shouldn’t be too noticeable once the finish goes on.

Veneer Repair

rest6.2

This table has a few veneer chips. Here’s a shot of one of them. My preferred method of veneer repair is to cut the damaged area to match the new veneer patch rather than try to cut the patch to match the damaged area. It just seems easier to get an accurate fit this way.

I first cut a new piece of veneer that’s just slightly larger than the chip, hold the patch over the chipped area and trace around it with a knife. I then remove the patch and continue cutting along the line I traced until the excess material comes off and then glue the new piece in place. On the subject of glue, when gluing these in with wood glue I will sometimes color the glue with some dark brown dye or water based paint and when the colored glue squeezes out it will fill in any small voids around the patch.

Gluing Loose Trim

rest3

There was a loose piece of trim on the front that needed to be glued. I cleaned out the joint, shot some glue in and clamped it up.

This trim piece appears to be made of ash wood. Ash appears often on Lane furniture. This one is a particularly nice piece of ash.

Pore Filling

rest8

This step is optional depending on the look you’re going for. This table has a walnut veneer and walnut is an open pore wood. If you’re going for a mirror smooth finish then the pores have to be filled before applying your topcoat otherwise the pores will be visible as small pits on the surface of the wood. If you’re going for a more natural look and don’t mind seeing the pores then you can skip this step.

For this piece I am using Timbermate filler. This is a water based filler and is pretty easy to work with. The first step is to apply a sealer coat of shellac so that the wood isn’t stained by the filler. I then colored the filler with some dark brown dye and then added some water until it’s the consistency of toothpaste. I then spread it around the surface with an old credit card. Since it’s water based it dries quickly but it can be sped up by warming it with a hair dryer. After it’s dry I lightly sand the excess off with 220 grit paper until the only filler left is in the pores of the wood.

rest9

Here it is after the excess filler is sanded off. Doesn’t look very attractive, does it? That will change once we get the finish on.

Stain and Topcoat

rest10

For this piece I’m using a walnut stain and a satin polyurethane topcoat. There’s not much to say about the staining process. I just wipe it on and then wipe it off after a few minutes. I do usually put a sealer coat of shellac or wood conditioner on before applying the stain. After applying the shellac I give it a light sanding with 320 grit. The shellac that’s left in the wood after sanding helps to even out absorption of the stain and helps prevent blotchiness.

After the stain is dry I wipe on a few coats of the polyurethane.

Done!

rest12

And here’s the finished product. I left out a few steps, including gluing the broken drawer pull back together, but maybe I’ll get to them in another restoration demo. I think it looks great. Another piece of furniture saved from the landfill!

perc5

Before and After

What better way to kick off the Dashner Design and Restoration page than with a before and after montage. I like a good challenge and this Lane end table had just enough challenges to keep things interesting. A little Citristip stripper and some elbow grease and voila! Underneath that paint and grime was some very attractive grain.

I’ve never seen this particular Lane table before but I like it. It’s hexagonal and who doesn’t like a good hexagon? The front opens up to a large storage space on the inside. Wonderful!

Before:

laneoct2

After:

lanoct5

lanoct4